Grizzly G0453 Instrukcja Użytkownika

MODEL G0453/G045415" & 20" MOBILE PLANERSOWNER'S MANUALCOPYRIGHT © MAY, 2005 BY GRIZZLY INDUSTRIAL, INC., REVISED NOVEMBER, 2012 (

-8-G0453/G0454 (Mfg. Since 3/08)The information contained herein is deemed accurate as of 6/9/2013 and represents our most recent product specificatio

-9-G0453/G0454 (Mfg. Since 3/08)ELECTRICAL EQUIPMENT INJURY RISKS. You can be shocked, burned, or killed by touching live electrical components or

-10-G0453/G0454 (Mfg. Since 3/08)WEARING PROPER APPAREL. Do not wearclothing, apparel or jewelry that can becomeentangled in moving pa

-11-G0453/G0454 (Mfg. Since 3/08)Additional Safety Instructions for PlanersOWNER'S MANUAL. This machine presents sig-nificant safety hazards t

-12-G0453/G0454 (Mfg. Since 3/08)SECTION 2: POWER SUPPLYAvailabilityBefore installing the machine, consider the avail-ability and proximity of the req

-13-G0453/G0454 (Mfg. Since 3/08)Extension CordsWe do not recommend using an extension cord with this machine. If you must use an extension

-14-G0453/G0454 (Mfg. Since 3/08)SECTION 3: SETUPThe following are needed to complete the setup process, but are not included with your machine:D

-15-G0453/G0454 (Mfg. Since 3/08)InventoryBox Inventory: (Figure 5) QtyA. Planer (Not Shown) ... 1B. Dust Hood ..

-16-G0453/G0454 (Mfg. Since 3/08)The unpainted surfaces of your machine are coated with a heavy-duty rust preventative that prevents corro

-17-G0453/G0454 (Mfg. Since 3/08)Site ConsiderationsFigure 6. Minimum working clearances.XYModel G0453 X = 42" Y = 28"Model G0454 X

This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, r

-18-G0453/G0454 (Mfg. Since 3/08)Lifting & Moving Base UnitThe Model G0453/G0454 is a heavy machine. Serious personal injury may occur if safe mo

-19 -G0453/G0454 (Mfg. Since 3/08)Figure 9. Installing the table height handwheel.Figure 10. Dust hood attached.4. Place the bushing on the handwheel

-20-G0453/G0454 (Mfg. Since 3/08)12. Using the short end of a clean hex wrench, dip it inside the fill hole and remove it.—If the end of t

-21-G0453/G0454 (Mfg. Since 3/08)Dust CollectionDO NOT operate the Model G0453/G0454 without an adequate dust collection system. This planer creates s

-22-G0453/G0454 (Mfg. Since 3/08)5. Verify that the machine is operating correctly by pushing the ON button.—When operating correctly, the machin

-23-G0453/G0454 (Mfg. Since 3/08)SECTION 4: OPERATIONSDamage to your eyes, lungs, and ears could result from using this machine without proper protect

-24-G0453/G0454 (Mfg. Since 3/08)Planing Tips• Use the full width of the planer. Alternate between the left, the right and the middle of the

-25-G0453/G0454 (Mfg. Since 3/08)Wood HardnessThe species of wood, as well as its condition, greatly affects the depth of cut the plane

-26-G0453/G0454 (Mfg. Since 3/08)Bed Roller HeightBed Roller Height Range ...0.002"–0.020"The correct height of the bed rol

-27-G0453/G0454 (Mfg. Since 3/08)Tools Needed QtyHex Wrench 3mm ... 1Wrench 14mm ...

Table of ContentsSECTION 5: ACCESSORIES ... 28SECTION 6: MAINTENANCE ... 30Schedule ...

-28-G0453/G0454 (Mfg. Since 3/08)SECTION 5: ACCESSORIESACCESSORIESFigure 20. Rotacator™ Precision Planer Tool.G1738—Rotacator™ Precision Planer ToolTh

-29-G0453/G0454 (Mfg. Since 3/08)T20501—Face Shield Crown Protector 4"T20502—Face Shield Crown Protector 7"T20503—Face Shield WindowT20448—E

-30-G0453/G0454 (Mfg. Since 3/08)SECTION 6: MAINTENANCEAlways disconnect power to the machine before performing maintenance. Failure to do this may re

-31-G0453/G0454 (Mfg. Since 3/08)LubricationYour planer features bearings that are lubricated and sealed at the factory. These bearing do not r

-32-G0453/G0454 (Mfg. Since 3/08)Table Height Chain & SprocketsThe table leadscrews are synchronized by the table height chain and sproc

-33-G0453/G0454 (Mfg. Since 3/08)SECTION 7: SERVICETroubleshootingMotor & ElectricalSymptom Possible Cause Possible SolutionMachine does not start

-34-G0453/G0454 (Mfg. Since 3/08)Motor & Electrical (continued)Symptom Possible Cause Possible SolutionMachine has vibration or noisy operation.8.

-35-G0453/G0454 (Mfg. Since 3/08)Machine Operation (continued)Symptom Possible Cause Possible SolutionFuzzy grain. 1. Workpiece has high moisture

-36-G0453/G0454 (Mfg. Since 3/08)Setting/Replacing KnivesPlaner knives are extremely sharp and can quickly cause a serious injury to your hands or fin

-37-G0453/G0454 (Mfg. Since 3/08)5. Jack Screws (G0453 & G0454): Insert the hex wrench into the jack screws through the access holes in

-2-G0453/G0454 (Mfg. Since 3/08)The Model G0453/G0454 Planer is designed to remove material in precise increments from the surface of na

-38-G0453/G0454 (Mfg. Since 3/08)2. Remove the V-belt cover from the left side of the machine to expose the belts, as shown in Figure 38. Note: A c

-39-G0453/G0454 (Mfg. Since 3/08)Table Height Chain TensionThe table height chain transfers movement from the elevation handwheel to the columns th

-40-G0453/G0454 (Mfg. Since 3/08)Feed Rollers, Chip Breaker & Pressure Bar HeightsA & BCDBDC(Bottom Dead Center)Figure 42. Planer component re

-41-G0453/G0454 (Mfg. Since 3/08)6. Move the feed speed knob to the neutral position to allow the infeed roller to freely rotate.7. Ke

-42-G0453/G0454 (Mfg. Since 3/08)Using Wood BlocksTools Needed QtyHex Wrenches 3, 5mm ...1 EachWrench or Socket 10mm ...

-43-G0453/G0454 (Mfg. Since 3/08)Positioning Chip DeflectorChip Deflector Gap Setting ...1⁄4"When properly distanced

-44-G0453/G0454 (Mfg. Since 3/08)4. If the distance measured in Step 3 is not equal to 1⁄4", then loosen the four hex bolts that s

-45-G0453/G0454 (Mfg. Since 3/08)Pulley AlignmentProper pulley alignment prevents premature V-belt wear and unnecessary load on the motor. The

-46-G0453/G0454 (Mfg. Since 3/08)SHOCK HAZARD. Working on wiring that is con-nected to a power source is extremely dangerous. Touching electrified p

-47-READ ELECTRICAL SAFETY ON PAGE 46!G0453/G0454 (Mfg. Since 3/08)2T16T3NO144T22T16T34T21L15L3NO133L2171897989596A1A2A2OL RelayNHD BTH-25ONOFFGrndCon

-3-G0453/G0454 (Mfg. Since 3/08)IdentificationFigure 1. General identification.MagneticON/OFFSwitchReturnRollersTableHeightHandwheelGearboxLiftingBar(

-48-READ ELECTRICAL SAFETY ON PAGE 46!G0453/G0454 (Mfg. Since 3/08)G0454 Wiring Diagram2T16T3NO144T22T16T34T21L15L3NO133L2171897989596A1A2A2ONOFFGrndC

-49-G0453/G0454 (Mfg. Since 3/08)1234567891112131415161718212526272829303133343536373839404142434445464748495051A5253545556575859606162636465666768697

-50-G0453/G0454 (Mfg. Since 3/08)G0453 Headstock Parts ListREF PART # DESCRIPTION REF PART # DESCRIPTION1 PVMX60 COGGED V-BELT MX-60 57 P0453057 FOAM

-51-G0453/G0454 (Mfg. Since 3/08)G0453 Table Breakdown203204205206207208209210211212213214215216208210209211213207REF PART # DESCRIPTION REF PART # DE

-52-G0453/G0454 (Mfg. Since 3/08)G0453 Columns Breakdown3033043053063073083093103113123133143153163173183193203213223233243253263273283293303313323333

-53-G0453/G0454 (Mfg. Since 3/08)G0453 Cabinet Stand Breakdown401402405406407408409410411412413414415416417418419420421422423424425426427428429430A431

-54-G0453/G0454 (Mfg. Since 3/08)G0453 Cabinet Stand Parts ListREF PART # DESCRIPTION REF PART # DESCRIPTION401 P0453401 RUBBER FOOT 430-3 P0453430-3

-55-G0453/G0454 (Mfg. Since 3/08)G0453 Gearbox Breakdown500A501502503504505506507508509510511512513514515516517518519520521522523524525526527528529530

-56-G0453/G0454 (Mfg. Since 3/08)G0453 Label PlacementSafety labels warn about machine hazards and ways to prevent injury. The owner of this machine M

-57-G0453/G0454 (Mfg. Since 3/08)G0454 Headstock Breakdown1233-13-23-33-445689101112131415171819202425262728293032343536373839404142434445464748495051

-4-G0453/G0454 (Mfg. Since 3/08)Internal ComponentsWorkpieceFigure 2. Workpiece path and major planing components (side cutaway view).A. Anti-Kickbac

-58-G0453/G0454 (Mfg. Since 3/08)G0454 Headstock Parts ListREF PART # DESCRIPTION REF PART # DESCRIPTION1 PVMX60 COGGED V-BELT MX-60 48 P0454048 WORM

-59-G0453/G0454 (Mfg. Since 3/08)G0454 Headstock Parts ListREF PART # DESCRIPTION REF PART # DESCRIPTION92 P0454092 SPROCKET 105-2 P0454105-2 TAPERED

-60-G0453/G0454 (Mfg. Since 3/08)G0454 Table Breakdown201202203204205206207208209210211212213204205207214210207206REF PART # DESCRIPTION REF PART # DE

-61-G0453/G0454 (Mfg. Since 3/08)G0454 Columns Breakdown3033043053063073083093103113123133143153163173183193203213223233243253263273283293303313323333

-62-G0453/G0454 (Mfg. Since 3/08)G0454 Cabinet Stand Breakdown401404405406407408409410411412413414415416417418419420421422423424425426427428429429-142

-63-G0453/G0454 (Mfg. Since 3/08)G0454 Cabinet Stand Parts ListREF PART # DESCRIPTION REF PART # DESCRIPTION401 P0453402 RELIEF BUSHING 428 PW01M FLAT

-64-G0453/G0454 (Mfg. Since 3/08)G0454 Gearbox Breakdown500A501502503504505506507508509510511512513514515516517518519520521522523524525526527528529530

-65-G0453/G0454 (Mfg. Since 3/08)71611811912012112233744544654454516G0454 Label PlacementSafety labels warn about machine hazards and ways to prevent

-66-G0453/G0454 (Mfg. Since 3/08)

CUT ALONG DOTTED LINEName _____________________________________________________________________________ Street ______________________________________

-5-G0453/G0454 (Mfg. Since 3/08)The information contained herein is deemed accurate as of 6/9/2013 and represents our most recent product specificatio

TAPE ALONG EDGES--PLEASE DO NOT STAPLEFOLD ALONG DOTTED LINEFOLD ALONG DOTTED LINEGRIZZLY INDUSTRIAL, INC.P.O. BOX 2069BELLINGHAM, WA 98227-2069Place

WARRANTY AND RETURNSGrizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchas

-6-G0453/G0454 (Mfg. Since 3/08)The information contained herein is deemed accurate as of 6/9/2013 and represents our most recent product specificatio

-7-G0453/G0454 (Mfg. Since 3/08)The information contained herein is deemed accurate as of 6/9/2013 and represents our most recent product specificatio